|
Post by Paulus17 on Aug 1, 2020 19:20:09 GMT
Those look smart Bob :TU:
|
|
|
Post by firemac on Aug 1, 2020 19:55:32 GMT
Those do look good, Bob. I recall that our first RAV, a 5-dr VX had those trims.
Not 100% certain but would have thought that the 3-dr and 5-dr would have the same door pulls. It would seem an unnecessary cost to have uniquely different ones. 🤔
|
|
|
Post by unclebob on Aug 1, 2020 20:18:45 GMT
Those do look good, Bob. I recall that our first RAV, a 5-dr VX had those trims. Not 100% certain but would have thought that the 3-dr and 5-dr would have the same door pulls. It would seem an unnecessary cost to have uniquely different ones. 🤔 Toyota logic says all the same but it’s being the guinea pig to try them 👍🏻 Could back cross reference the 3 door part numbers to see if same as 5 door.
|
|
|
Post by unclebob on Aug 2, 2020 15:33:01 GMT
As with my last 3 door Rav4 always felt anything in the boot was vulnerable by not have a parcel shelf, so decided to make one for this car this morning . Cardboard template was the start of the job...only had half of it left over from last time🙄 Then a offcut sheet Of 15mm ply. Covered It in soft foam. Then grey stretchy acoustic cloth in grey . Run out of time.....let’s hope it fits when I try it out later on 👍🏻👍🏻
|
|
|
Post by three5 on Aug 2, 2020 15:37:43 GMT
As with my last 3 door Rav4 always felt anything in the boot was vulnerable by not have a parcel shelf, so decided to make one for this car this morning . Cardboard template was the start of the job...only had half of it left over from last time🙄 Then a offcut sheet Of 15mm ply. Covered It in soft foam. Then grey stretchy acoustic cloth in grey . Run out of time.....let’s hope it fits when I try it out later on 👍🏻👍🏻 How are you going to fasten in place Bob?
|
|
|
Post by unclebob on Aug 2, 2020 15:51:06 GMT
As it goes full width once the seats are adjust back it becomes a tight fit , and the holes I drilled on the underside of the board locate on the bag hooks each side at the back .
|
|
|
Post by three5 on Aug 2, 2020 16:34:42 GMT
As it goes full width once the seats are adjust back it becomes a tight fit , and the holes I drilled on the underside of the board locate on the bag hooks each side at the back . Nice one Bob!
|
|
|
Post by Paulus17 on Aug 2, 2020 16:49:51 GMT
Looking good again Bob :TU: I remember the last one you made and was thinking of making one but we do move the rear seats forward a lot when we go shopping to give that extra bit of space. I suppose it could be hinged in two halves so it could pull out or move up??
|
|
|
Post by unclebob on Aug 2, 2020 17:52:41 GMT
All fitted 😎 Fits tight into the corners .
|
|
|
Post by unclebob on Aug 2, 2020 17:58:42 GMT
|
|
|
Post by firemac on Aug 2, 2020 18:28:07 GMT
Nice job with the parcel shelf, Bob. I've never bothered mainly because the rear seats sre nearly always folded up or out of the car entirely. We tend to only travel 2-up and having the seats out of the way makes it easier to tote groceries and B&Q stuff.
|
|
|
Post by unclebob on Aug 5, 2020 17:58:59 GMT
|
|
|
Post by three5 on Aug 5, 2020 18:06:28 GMT
Nice job Bob, I need to do that job on mine as some of the coating on the arms ( over the aluminium casting ) has come off. Didn't consider painting them but something like Smoothrite ought to work.
|
|
|
Post by unclebob on Aug 5, 2020 18:17:18 GMT
Have all new clips from Toyota for the windscreen /battery panel ..just need the weather on my side over the next few days 👍🏻
|
|
|
Post by davrav on Aug 5, 2020 22:10:21 GMT
Nice job Bob :TU:
|
|